samblue 2006-8-7 20:10
25133-730-Requirements for support of radio resource management (FDD)
25133-730-Requirements for support of radio resource management (FDD).pdf
Contents
Foreword .........................................................................................................................................................12
1 Scope.....................................................................................................................................................13
2 References .............................................................................................................................................13
3 Definitions, symbols and abbreviations .................................................................................................14
3.1 Definitions ...................................................................................................................................................... 14
3.2 Symbols .......................................................................................................................................................... 14
3.3 Abbreviations.................................................................................................................................................. 15
3.4 Test tolerances ................................................................................................................................................ 16
4 Idle Mode Tasks....................................................................................................................................16
4.1 Cell Selection.................................................................................................................................................. 16
4.1.1 Introduction............................................................................................................................................... 16
4.2 Cell Re-selection............................................................................................................................................. 16
4.2.1 Introduction............................................................................................................................................... 16
4.2.2 Requirements ............................................................................................................................................ 16
4.2.2.1 Measurement and evaluation of cell selection criteria S of serving cell............................................... 16
4.2.2.2 Measurements of intra-frequency cells................................................................................................. 17
4.2.2.3 Measurements of inter-frequency FDD cells........................................................................................ 17
4.2.2.4 Measurements of inter-frequency TDD cells........................................................................................ 17
4.2.2.5 Measurements of inter-RAT GSM cells ............................................................................................... 18
4.2.2.6 Evaluation of cell re-selection criteria.................................................................................................. 18
4.2.2.7 Maximum interruption in paging reception .......................................................................................... 18
4.2.2.8 Number of cells in cell lists .................................................................................................................. 19
4.2.2.9 Additional requirements for measurement of inter-frequency and inter-RAT cells when MBMS
reception is active ................................................................................................................................ 19
5 UTRAN Connected mode mobility........................................................................................................20
5.1 FDD/FDD Soft Handover............................................................................................................................... 20
5.1.1 Introduction............................................................................................................................................... 20
5.1.2 Requirements ............................................................................................................................................ 20
5.1.2.1 Active set dimension ............................................................................................................................ 20
5.1.2.2 Active set update delay......................................................................................................................... 20
5.1.2.3 Interruption Time................................................................................................................................. 21
5.2 FDD/FDD Hard Handover.............................................................................................................................. 21
5.2.1 Introduction............................................................................................................................................... 21
5.2.2 Requirements ............................................................................................................................................ 21
5.2.2.1 Hard handover delay............................................................................................................................ 21
5.2.2.2 Interruption time.................................................................................................................................. 21
5.3 FDD/TDD Handover ...................................................................................................................................... 22
5.3.1 Introduction............................................................................................................................................... 22
5.3.2 Requirements ............................................................................................................................................ 22
5.3.2.1 FDD/TDD handover delay ................................................................................................................... 22
5.3.2.2 Interruption time.................................................................................................................................. 23
5.4 FDD/GSM Handover...................................................................................................................................... 23
5.4.1 Introduction............................................................................................................................................... 23
5.4.2 Requirements ............................................................................................................................................ 24
5.4.2.1 Handover delay.................................................................................................................................... 24
5.4.2.2 Interruption time.................................................................................................................................. 24
5.5 Cell Re-selection in CELL_FACH.................................................................................................................. 24
5.5.1 Introduction............................................................................................................................................... 24
5.5.2 Requirements ............................................................................................................................................ 24
5.5.2.1 Cell re-selection delay .......................................................................................................................... 25
5.5.2.1.1 Intra frequency cell reselection ....................................................................................................... 25
5.5.2.1.2 Inter frequency cell reselection ....................................................................................................... 25
5.5.2.1.3 FDD-TDD cell reselection.............................................................................................................. 26
5.5.2.1.4 UTRAN-GSM Cell Reselection...................................................................................................... 26
3GPP
Release 7 4 3GPP TS 25.133 V7.3.0 (2006-03)
5.5.2.2 Interruption time.................................................................................................................................. 27
5.5.2.2.1 FDD-FDD cell reselection .............................................................................................................. 27
5.5.2.2.2 FDD-TDD cell reselection.............................................................................................................. 27
5.5.2.2.3 FDD-GSM cell reselection.............................................................................................................. 28
5.5.2.3 Measurement and evaluation of cell selection criteria S of serving cell............................................... 28
5.6 Cell Re-selection in CELL_PCH..................................................................................................................... 29
5.6.1 Introduction............................................................................................................................................... 29
5.6.2 Requirements ............................................................................................................................................ 29
5.7 Cell Re-selection in URA_PCH....................................................................................................................... 29
5.7.1 Introduction............................................................................................................................................... 29
5.7.2 Requirements ............................................................................................................................................ 29
5.8 RACH reporting.............................................................................................................................................. 29
5.8.1 Introduction............................................................................................................................................... 29
5.8.2 Requirements ............................................................................................................................................ 29
5.9 Inter-RAT cell change order from UTRAN in CELL_DCH and CELL_FACH............................................. 30
5.9.1 Introduction............................................................................................................................................... 30
5.9.2 Requirements ............................................................................................................................................ 30
5.9.2.1 Delay ................................................................................................................................................... 30
5.9.2.2 Interruption time.................................................................................................................................. 30
5.10 Serving HS-DSCH cell change........................................................................................................................ 31
5.10.3 Introduction............................................................................................................................................... 31
5.10.2 Requirements ............................................................................................................................................ 31
5.10.2.1 Serving HS-DSCH cell change delay ................................................................................................... 31
5.10.2.2 Interruption time.................................................................................................................................. 31
6 RRC Connection Control .......................................................................................................................32
6.1 RRC Re-establishment.................................................................................................................................... 32
6.1.1 Introduction............................................................................................................................................... 32
6.1.2 Requirements ............................................................................................................................................ 32
6.1.2.1 UE Re-establishment delay requirement .............................................................................................. 32
6.2 Void ................................................................................................................................................................ 33
6.3 Random Access .............................................................................................................................................. 33
6.3.1 Introduction............................................................................................................................................... 33
6.3.2 Requirements ............................................................................................................................................ 33
6.3.2.1 Correct behaviour when receiving an ACK.......................................................................................... 33
6.3.2.2 Correct behaviour when receiving an NACK....................................................................................... 33
6.3.2.3 Correct behaviour at Time-out.............................................................................................................. 33
6.3.2.4 Correct behaviour when reaching maximum transmit power............................................................... 33
6.4 Transport format combination selection in UE................................................................................................ 34
6.4.1 Introduction............................................................................................................................................... 34
6.4.2 Requirements ............................................................................................................................................ 34
6.5 Maximum allowed UL TX Power ................................................................................................................... 36
6.6 Void ................................................................................................................................................................ 36
7 Timing and Signalling characteristics ....................................................................................................37
7.1 UE Transmit Timing....................................................................................................................................... 37
7.1.1 Introduction............................................................................................................................................... 37
7.1.2 Requirements ............................................................................................................................................ 37
7.2 UE Receive - Transmit Time Difference ......................................................................................................... 37
7.2.1 Introduction............................................................................................................................................... 37
7.2.2 Requirements ............................................................................................................................................ 38
7.3 UE timer accuracy .......................................................................................................................................... 38
7.3.1 Introduction............................................................................................................................................... 38
7.3.2 Requirements ............................................................................................................................................ 38
7.4 PRACH Burst timing accuracy....................................................................................................................... 38
7.4.1 Introduction............................................................................................................................................... 38
7.4.2 Requirements ............................................................................................................................................ 38
8 UE Measurements Procedures ...............................................................................................................39
8.1 General Measurement Requirements in CELL_DCH State............................................................................. 39
8.1.1 Introduction............................................................................................................................................... 39
8.1.2 Requirements ............................................................................................................................................ 39
8.1.2.1 UE Measurement Capability ................................................................................................................ 39
3GPP
Release 7 5 3GPP TS 25.133 V7.3.0 (2006-03)
8.1.2.2 FDD intra frequency measurements ..................................................................................................... 40
8.1.2.2.1 Identification of a new cell.............................................................................................................. 40
8.1.2.2.1.1 Identification of a new cell using IPDL gaps ............................................................................ 40
8.1.2.2.2 UE CPICH measurement capability................................................................................................ 41
8.1.2.2.2.1 Capabilities for measurements during IPDL gaps..................................................................... 41
8.1.2.2.3 Periodic Reporting .......................................................................................................................... 41
8.1.2.2.4 Event-triggered Periodic Reporting ................................................................................................ 41
8.1.2.2.5 Event Triggered Reporting.............................................................................................................. 42
8.1.2.3 FDD inter frequency measurements ..................................................................................................... 42
8.1.2.3.1 Identification of a new cell.............................................................................................................. 42
8.1.2.3.2 UE CPICH measurement capability................................................................................................ 43
8.1.2.3.3 Periodic Reporting .......................................................................................................................... 43
8.1.2.3.4 Event Triggered Reporting.............................................................................................................. 43
8.1.2.4 TDD measurements .............................................................................................................................. 43
8.1.2.4.1 Identification of a new cell.............................................................................................................. 44
8.1.2.4.2 P-CCPCH RSCP measurement period............................................................................................ 45
8.1.2.4.3 Periodic Reporting .......................................................................................................................... 45
8.1.2.4.4 Event Triggered Reporting.............................................................................................................. 45
8.1.2.5 GSM measurements............................................................................................................................. 46
8.1.2.5.1 GSM carrier RSSI........................................................................................................................... 46
8.1.2.5.2 BSIC verification ............................................................................................................................ 47
8.1.2.5.3 Periodic Reporting .......................................................................................................................... 50
8.1.2.5.4 Event Triggered Reporting.............................................................................................................. 50
8.2 Measurements in CELL_DCH State with special requirements...................................................................... 50
8.2.1 Introduction............................................................................................................................................... 50
8.2.2 Requirements ............................................................................................................................................ 51
8.3 Capabilities for Support of Event Triggering and Reporting Criteria in CELL_DCH state ............................ 51
8.3.1 Introduction............................................................................................................................................... 51
8.3.2 Requirements ............................................................................................................................................ 51
8.4 Measurements in CELL_FACH State.............................................................................................................. 52
8.4.1 Introduction............................................................................................................................................... 52
8.4.2 Requirements ............................................................................................................................................ 52
8.4.2.1 UE Measurement Capability ................................................................................................................ 52
8.4.2.2 FDD intra frequency measurements ..................................................................................................... 53
8.4.2.2.1 Identification of a new cell.............................................................................................................. 53
8.4.2.2.2 UE CPICH measurement capability................................................................................................ 54
8.4.2.2.2.1 Capabilities for measurements during IPDL gaps..................................................................... 54
8.4.2.2.3 RACH reporting............................................................................................................................. 55
8.4.2.3 FDD inter frequency measurements ..................................................................................................... 55
8.4.2.3.1 Identification of a new cell.............................................................................................................. 55
8.4.2.3.2 UE CPICH measurement capability................................................................................................ 55
8.4.2.4 TDD measurements .............................................................................................................................. 56
8.4.2.4.1 Identification of a new cell.............................................................................................................. 56
8.4.2.4.2 P-CCPCH RSCP measurement period............................................................................................ 57
8.4.2.5 GSM measurements............................................................................................................................. 58
8.4.2.5.1 GSM carrier RSSI........................................................................................................................... 58
8.4.2.5.2 BSIC verification ............................................................................................................................ 59
8.5 Capabilities for Support of Event Triggering and Reporting Criteria in CELL_FACH state .......................... 61
8.5.1 Introduction............................................................................................................................................... 61
8.5.2 Requirements ............................................................................................................................................ 61
9 Measurements Performance Requirements ............................................................................................61
9.1 Measurement Performance for UE .................................................................................................................. 61
9.1.1 CPICH RSCP ............................................................................................................................................ 62
9.1.1.1 Intra frequency measurements accuracy............................................................................................... 62
9.1.1.1.1 Absolute accuracy requirement....................................................................................................... 62
9.1.1.1.2 Relative accuracy requirement........................................................................................................ 62
9.1.1.2 Inter frequency measurement accuracy ................................................................................................ 63
9.1.1.2.1 Relative accuracy requirement........................................................................................................ 63
9.1.1.3 CPICH RSCP measurement report mapping ........................................................................................ 64
9.1.2 CPICH Ec/Io ............................................................................................................................................. 64
9.1.2.1 Intra frequency measurements accuracy............................................................................................... 64
3GPP
Release 7 6 3GPP TS 25.133 V7.3.0 (2006-03)
9.1.2.1.1 Absolute accuracy requirement....................................................................................................... 64
9.1.2.1.2 Relative accuracy requirement........................................................................................................ 65
9.1.2.2 Inter frequency measurement accuracy ................................................................................................ 65
9.1.2.2.1 Absolute accuracy requirement....................................................................................................... 65
9.1.2.2.2 Relative accuracy requirement........................................................................................................ 66
9.1.2.3 CPICH Ec/Io measurement report mapping ......................................................................................... 67
9.1.3 UTRA Carrier RSSI .................................................................................................................................. 67
9.1.3.1 Absolute accuracy requirement ............................................................................................................ 67
9.1.3.2 Relative accuracy requirement ............................................................................................................. 67
9.1.3.3 UTRA Carrier RSSI measurement report mapping.............................................................................. 68
9.1.4 GSM carrier RSSI ..................................................................................................................................... 68
9.1.5 Transport channel BLER........................................................................................................................... 69
9.1.5.1 BLER measurement requirement ......................................................................................................... 69
9.1.5.2 Transport channel BLER measurement report mapping....................................................................... 69
9.1.6 UE transmitted power ............................................................................................................................... 69
9.1.6.1 Accuracy requirement.......................................................................................................................... 69
9.1.6.2 UE transmitted power measurement report mapping ........................................................................... 69
9.1.7 SFN-CFN observed time difference........................................................................................................... 70
9.1.7.1 Intra frequency measurement requirement ........................................................................................... 70
9.1.7.2 Inter frequency measurement requirement ........................................................................................... 71
9.1.7.3 SFN-CFN observed time difference measurement report mapping...................................................... 72
9.1.8 SFN-SFN observed time difference ........................................................................................................... 72
9.1.8.1 SFN-SFN observed time difference type 1........................................................................................... 72
9.1.8.1.1 Measurement requirement............................................................................................................... 72
9.1.8.1.2 SFN-SFN observed time difference type 1 measurement report mapping...................................... 73
9.1.8.2 SFN-SFN observed time difference type 2........................................................................................... 73
9.1.8.2.1 Intra frequency measurement requirement accuracy without IPDL period active .......................... 73
9.1.8.2.2 Intra frequency measurement requirement accuracy with IPDL period active ............................... 74
9.1.8.2.3 Inter frequency measurement requirement accuracy....................................................................... 75
9.1.8.2.4 SFN-SFN observed time difference type 2 measurement report mapping...................................... 75
9.1.9 UE Rx-Tx time difference......................................................................................................................... 76
9.1.9.1 UE Rx-Tx time difference type 1 ......................................................................................................... 76
9.1.9.1.1 Measurement requirement............................................................................................................... 76
9.1.9.1.2 UE Rx-Tx time difference type 1 measurement report mapping .................................................... 76
9.1.9.2 UE Rx-Tx time difference type 2 ......................................................................................................... 76
9.1.9.2.1 Measurement requirement............................................................................................................... 76
9.1.9.2.2 UE Rx-Tx time difference type 2 measurement report mapping .................................................... 77
9.1.10 Void........................................................................................................................................................... 77
9.1.11 P-CCPCH RSCP ....................................................................................................................................... 77
9.1.11.1 Absolute accuracy requirements........................................................................................................... 77
9.1.11.1.1 3.84 Mcps TDD Option .................................................................................................................. 77
9.1.11.1.2 1.28 Mcps TDD Option .................................................................................................................. 78
9.1.11.2 P-CCPCH RSCP measurement report mapping ................................................................................... 78
9.1.12 UE GPS Timing of Cell Frames for UE positioning.................................................................................. 78
9.1.12.1 UE GPS timing of Cell Frames for UE positioning measurement report mapping .............................. 78
9.1.13 UE transmission power headroom ............................................................................................................. 79
9.1.13.1 Delay requirement ............................................................................................................................... 79
9.1.13.2 Measurement period requirement ......................................................................................................... 79
9.1.13.3 UE transmission power headroom measurement report mapping ........................................................ 80
9.1.13.4 UE transmission power headroom measurement report accuracy ........................................................ 81
9.2 Measurements Performance for UTRAN ........................................................................................................ 81
9.2.1 Received total wideband power ................................................................................................................. 81
9.2.1.1 Absolute accuracy requirement ............................................................................................................ 81
9.2.1.2 Relative accuracy requirement ............................................................................................................. 82
9.2.1.3 Received total wideband power measurement report mapping ............................................................ 82
9.2.2 SIR ............................................................................................................................................................ 82
9.2.2.1 Accuracy requirement.......................................................................................................................... 82
9.2.2.2 SIR measurement report mapping ........................................................................................................ 82
9.2.3 SIRerror ....................................................................................................................................................... 83
9.2.3.1 Accuracy requirement.......................................................................................................................... 83
9.2.3.2 SIRerror measurement report mapping ................................................................................................... 83
9.2.4 Transmitted carrier power .......................................................................................................................... 83
3GPP
Release 7 7 3GPP TS 25.133 V7.3.0 (2006-03)
9.2.4.1 Accuracy requirement.......................................................................................................................... 84
9.2.4.2 Transmitted carrier power measurement report mapping..................................................................... 84
9.2.5 Transmitted code power ............................................................................................................................. 84
9.2.5.1 Absolute accuracy requirement ............................................................................................................ 84
9.2.5.2 Relative accuracy requirement ............................................................................................................. 84
9.2.5.3 Transmitted code power measurement report mapping........................................................................ 84
9.2.6 Void........................................................................................................................................................... 85
9.2.7 Physical channel BER............................................................................................................................... 85
9.2.7.1 Accuracy requirement.......................................................................................................................... 85
9.2.7.2 Physical channel BER measurement report mapping........................................................................... 85
9.2.8 Round trip time ......................................................................................................................................... 85
9.2.8.1 Absolute accuracy requirement ............................................................................................................ 86
9.2.8.2 Round trip time measurement report mapping ..................................................................................... 86
9.2.9 Transport Channel BER ............................................................................................................................. 86
9.2.9.1 Accuracy requirement.......................................................................................................................... 86
9.2.9.2 Transport channel BER measurement report mapping......................................................................... 86
9.2.10 UTRAN GPS Timing of Cell Frames for UE positioning.......................................................................... 87
9.2.10.1 Accuracy requirement.......................................................................................................................... 87
9.2.10.2 UTRAN GPS timing of Cell Frames for UE positioning measurement report mapping...................... 87
9.2.11 PRACH Propagation delay......................................................................................................................... 88
9.2.11.1 Accuracy requirement.......................................................................................................................... 88
9.2.11.1.1 PRACH Propagation delay ............................................................................................................. 88
9.2.11.1.2 Void ............................................................................................................................................... 88
9.2.11.2 PRACH Propagation delay measurement report mapping ................................................................... 88
9.2.12 Acknowledged PRACH preambles ............................................................................................................ 88
9.2.12.1 Acknowledged PRACH preambles measurement report mapping....................................................... 88
9.2.13 Void........................................................................................................................................................... 89
9.2.14 Void........................................................................................................................................................... 89
9.2.15 SFN-SFN observed time difference ........................................................................................................... 89
9.2.15.1 Accuracy requirement.......................................................................................................................... 89
9.2.15.1.1 Accuracy requirement without IPDL.............................................................................................. 89
9.2.15.1.2 Accuracy requirement with IPDL................................................................................................... 89
9.2.15.2 SFN-SFN observed time difference measurement report mapping ...................................................... 89
9.2.16 Transmitted carrier power of all codes not used for HS-PDSCH, HS-SCCH, E-AGCH, E-RGCH or
E-HICH transmission ................................................................................................................................ 90
9.2.16.1 Accuracy requirement.......................................................................................................................... 90
9.2.16.2 Measurement report mapping for transmitted carrier power of all codes not used for HS-PDSCH,
HS-SCCH, E-AGCH, E-RGCH or E-HICH transmission.................................................................... 90
9.2.17 DL Transmission Branch Load .................................................................................................................. 91
9.2.17.1 Accuracy requirement.......................................................................................................................... 91
9.2.17.2 DL Transmission Branch Load measurement report mapping ............................................................. 91
Annex A (normative): Test Cases .......................................................................................................93
A.1 Purpose of Annex..................................................................................................................................93
A.2 Requirement classification for statistical testing....................................................................................93
A.2.1 Types of requirements in TS 25.133................................................................................................................ 93
A.3 Reserved for Future Use.........................................................................................................................94
A.4 Idle Mode ..............................................................................................................................................94
A.4.1 Cell selection .................................................................................................................................................. 94
A.4.2 Cell Re-Selection ............................................................................................................................................ 94
A.4.2.1 Scenario 1: Single carrier case ................................................................................................................... 95
A.4.2.1.1 Test Purpose and Environment............................................................................................................. 95
A.4.2.1.2 Test Requirements ............................................................................................................................... 96
A.4.2.2 Scenario 2: Multi carrier case..................................................................................................................... 96
A.4.2.2.1 Test Purpose and Environment............................................................................................................. 96
A.4.2.2.2 Test Requirements ............................................................................................................................... 97
A.4.3 UTRAN to GSM Cell Re-Selection................................................................................................................. 98
A.4.3.1 Scenario 1.................................................................................................................................................. 98
A.4.3.1.1 Test Purpose and Environment............................................................................................................. 98
3GPP
Release 7 8 3GPP TS 25.133 V7.3.0 (2006-03)
A.4.3.1.2 Test Requirements ............................................................................................................................... 99
A.4.3.2 Scenario 2.................................................................................................................................................. 99
A.4.3.2.1 Test Purpose and Environment............................................................................................................. 99
A.4.3.2.2 Test Requirements .............................................................................................................................. 100
A.4.3.3 Scenario 3................................................................................................................................................ 101
A.4.3.3.1 Test Purpose and Environment........................................................................................................... 101
A.4.3.3.2 Test Requirements .............................................................................................................................. 102
A.4.3.4 Scenario 4................................................................................................................................................ 102
A.4.3.4.1 Test Purpose and Environment........................................................................................................... 102
A.4.3.4.2 Test Requirements .............................................................................................................................. 104
A.4.4 FDD/TDD Cell Re-selection......................................................................................................................... 105
A.4.4.1 Test Purpose and Environment ................................................................................................................ 105
A.4.4.1.1 3.84 Mcps TDD Option ...................................................................................................................... 105
A.4.4.1.2 1.28 Mcps TDD Option ...................................................................................................................... 106
A.4.4.2 Test Requirements................................................................................................................................... 107
A.5 UTRAN Connected Mode Mobility.....................................................................................................108
A.5.1 FDD/FDD Soft Handover............................................................................................................................. 108
A.5.1.1 Test Purpose and Environment ................................................................................................................ 108
A.5.1.1.1 Test procedure ................................................................................................................................... 109
A.5.1.2 Test Requirements................................................................................................................................... 109
A.5.2 FDD/FDD Hard Handover............................................................................................................................ 109
A.5.2.1 Handover to intra-frequency cell.............................................................................................................. 109
A.5.2.1.1 Test Purpose and Environment........................................................................................................... 109
A.5.2.1.2 Test Requirements .............................................................................................................................. 110
A.5.2.2 Handover to inter-frequency cell.............................................................................................................. 110
A.5.2.2.1 Test Purpose and Environment........................................................................................................... 110
A.5.2.2.2 Test Requirements .............................................................................................................................. 111
A.5.3 Void .............................................................................................................................................................. 112
A.5.4 Inter-system Handover from UTRAN FDD to GSM..................................................................................... 112
A.5.4.1 Test Purpose and Environment........................................................................................................... 112
A.5.4.2 Test Requirements .............................................................................................................................. 114
A.5.5 Cell Re-selection in CELL_FACH................................................................................................................ 114
A.5.5.1 One frequency present in neighbour list................................................................................................... 114
A.5.5.1.1 Test Purpose and Environment........................................................................................................... 114
A.5.5.1.2 Test Requirements .............................................................................................................................. 115
A.5.5.2 Two frequencies present in the neighbour list.......................................................................................... 116
A.5.5.2.1 Test Purpose and Environment........................................................................................................... 116
A.5.5.2.2 Test Requirements .............................................................................................................................. 117
A.5.5.3 Cell Reselection to GSM.......................................................................................................................... 118
A.5.5.3.1 Test Purpose and Environment........................................................................................................... 118
A.5.5.3.2 Test Requirements .............................................................................................................................. 120
A.5.5.4 Cell Reselection during an MBMS session, one frequency present in neighbour list .............................. 120
A.5.5.4.1 Test Purpose and Environment........................................................................................................... 120
A.5.5.4.2 Test Requirements .............................................................................................................................. 123
A.5.6 Cell Re-selection in CELL_PCH................................................................................................................... 123
A.5.6.1 One frequency present in the neighbour list............................................................................................. 123
A.5.6.1.1 Test Purpose and Environment........................................................................................................... 123
A.5.6.1.2 Test Requirements .............................................................................................................................. 124
A.5.6.2 Two frequencies present in the neighbour list.......................................................................................... 125
A.5.6.2.1 Test Purpose and Environment........................................................................................................... 125
A.5.6.2.2 Test Requirements .............................................................................................................................. 126
A.5.6.3 Cell re-selection during an MBMS session, one UTRAN inter-frequency and 4 GSM cells present in
the neighbour list..................................................................................................................................... 126
A.5.6.3.1 Test Purpose and Environment........................................................................................................... 126
A.5.6.3.2 Test Requirements .............................................................................................................................. 128
A.5.7 Cell Re-selection in URA_PCH..................................................................................................................... 129
A.5.7.1 One frequency present in the neighbour list............................................................................................. 129
A.5.7.1.1 Test Purpose and Environment........................................................................................................... 129
A.5.7.1.2 Test Requirements .............................................................................................................................. 130
A.5.7.2 Two frequencies present in the neighbour list.......................................................................................... 130
A.5.7.2.1 Test Purpose and Environment........................................................................................................... 130
3GPP
Release 7 9 3GPP TS 25.133 V7.3.0 (2006-03)
A.5.7.2.2 Test Requirements .............................................................................................................................. 131
A.5.8 Serving HS-DSCH cell change...................................................................................................................... 132
A.5.8.1 Test Purpose and Environment ................................................................................................................ 132
A.5.8.1.1 Test procedure ................................................................................................................................... 133
A.5.8.2 Test Requirements................................................................................................................................... 133
A.6 RRC Connection Control .....................................................................................................................133
A.6.1 RRC Re-establishment delay ......................................................................................................................... 133
A.6.1.1 Test Purpose and Environment ................................................................................................................ 133
A.6.1.1.1 TEST 1 .............................................................................................................................................. 134
A.6.1.1.2 TEST 2 .............................................................................................................................................. 134
A.6.1.2 Test Requirements................................................................................................................................... 135
A.6.1.2.1 Test 1 ................................................................................................................................................. 135
A.6.1.2.2 Test 2 ................................................................................................................................................. 136
A.6.2 Random Access ............................................................................................................................................ 136
A.6.2.1 Test Purpose and Environment ................................................................................................................ 136
A.6.2.2 Test Requirements................................................................................................................................... 138
A.6.2.2.1 Correct behaviour when receiving an ACK........................................................................................ 138
A.6.2.2.2 Correct behaviour when receiving an NACK..................................................................................... 138
A.6.2.2.3 Correct behaviour at Time-out............................................................................................................ 138
A.6.2.2.4 Correct behaviour when reaching maximum transmit power............................................................. 138
A.6.3 Void .............................................................................................................................................................. 138
A.6.4 Transport format combination selection in UE.............................................................................................. 138
A.6.4.1 Test Purpose and Environment ................................................................................................................ 138
A.6.4.1.1 Interactive or Background, PS, UL: 64 kbps ...................................................................................... 139
A.6.4.2 Test Requirements................................................................................................................................... 140
A.6.4.2.1 Interactive or Background, PS, UL: 64 kbps ...................................................................................... 140
A.6.5 Void .............................................................................................................................................................. 140
A.7 Timing and Signalling Characteristics .................................................................................................141
A.7.1 UE Transmit Timing..................................................................................................................................... 141
A.7.1.1 Test Purpose and Environment ................................................................................................................ 141
A.7.1.2 Test Requirements................................................................................................................................... 141
A.8 UE Measurements Procedures .............................................................................................................142
A.8.1 FDD intra frequency measurements .............................................................................................................. 142
A.8.1.1 Event triggered reporting in AWGN propagation conditions................................................................... 142
A.8.1.1.1 Test Purpose and Environment........................................................................................................... 142
A.8.1.1.2 Test Requirements .............................................................................................................................. 143
A.8.1.2 Event triggered reporting of multiple neighbours in AWGN propagation condition............................... 143
A.8.1.2.1 Test Purpose and Environment........................................................................................................... 143
A.8.1.2.2 Test Requirements .............................................................................................................................. 144
A.8.1.3 Event triggered reporting of two detectable neighbours in AWGN propagation condition ..................... 145
A.8.1.3.1 Test Purpose and Environment........................................................................................................... 145
A.8.1.3.2 Test Requirements .............................................................................................................................. 146
A.8.1.4 Correct reporting of neighbours in fading propagation condition ............................................................ 146
A.8.1.4.1 Test Purpose and Environment........................................................................................................... 146
A.8.1.4.2 Test Requirements .............................................................................................................................. 147
A.8.1.5 Event triggered reporting of multiple neighbour cells in Case 1 fading condition................................... 147
A.8.1.5.1 Test Purpose and Environment........................................................................................................... 147
A.8.1.5.2 Test Requirements .............................................................................................................................. 148
A.8.1.6 Event triggered reporting of multiple neighbour cells in Case 3 fading condition................................... 149
A.8.1.6.1 Test Purpose and Environment........................................................................................................... 149
A.8.1.6.2 Test Requirements .............................................................................................................................. 150
A.8.2 FDD inter frequency measurements .............................................................................................................. 150
A.8.2.1 Correct reporting of neighbours in AWGN propagation condition.......................................................... 150
A.8.2.1.1 Test Purpose and Environment........................................................................................................... 150
A.8.2.1.2 Test Requirements .............................................................................................................................. 151
A.8.2.2 Correct reporting of neighbours in Fading propagation condition ........................................................... 152
A.8.2.2.1 Test Purpose and Environment........................................................................................................... 152
A.8.2.2.2 Test Requirements .............................................................................................................................. 152
A.8.2.3 Correct reporting of neighbours in fading propagation condition using TGL1=14.................................. 153
A.8.2.3.1 Test Purpose and Environment........................................................................................................... 153
3GPP
Release 7 10 3GPP TS 25.133 V7.3.0 (2006-03)
A.8.2.3.2 Test Requirements .............................................................................................................................. 153
A.8.3 Void .............................................................................................................................................................. 154
A.8.4 GSM measurements...................................................................................................................................... 154
A.8.4.1 Correct reporting of GSM neighbours in AWGN propagation condition ................................................ 154
A.8.4.1.1 Test Purpose and Environment........................................................................................................... 154
A.8.4.1.1.1 Test 1. With BSIC verification required ....................................................................................... 155
A.8.4.1.1.2 Test 2: Without BSIC verification required .................................................................................. 156
A.8.4.1.2 Test Requirements .............................................................................................................................. 157
A.8.4.1.2.1 TEST 1 With BSIC verification required...................................................................................... 157
A.8.4.1.2.2 TEST 2 Without BSIC verification required................................................................................. 157
A.8.5 Combined Interfrequency and GSM measurements ...................................................................................... 158
A.8.5.1 Correct reporting of neighbours in AWGN propagation condition.......................................................... 158
A.8.5.1.1 Test Purpose and Environment........................................................................................................... 158
A.8.5.1.2 Test Requirements .............................................................................................................................. 159
A.9 Measurement Performance Requirements............................................................................................160
A.9.1 Measurement Performance for UE ................................................................................................................ 160
A.9.1.1 CPICH RSCP .......................................................................................................................................... 160
A.9.1.1.1 Test Purpose and Environment........................................................................................................... 160
A.9.1.1.1.1 Intra frequency test parameters ..................................................................................................... 160
A.9.1.1.1.2 Inter frequency test parameters ..................................................................................................... 161
A.9.1.1.2 Test Requirements .............................................................................................................................. 162
A.9.1.2 CPICH Ec/Io ........................................................................................................................................... 162
A.9.1.2.1 Test Purpose and Environment........................................................................................................... 162
A.9.1.2.1.1 Intra frequency test parameters ..................................................................................................... 162
A.9.1.2.1.2 Inter frequency test parameters ..................................................................................................... 163
A.9.1.2.2 Test Requirements .............................................................................................................................. 164
A.9.1.3 UTRA Carrier RSSI ................................................................................................................................ 165
A.9.1.3.1 Test Purpose and Environment........................................................................................................... 165
A.9.1.3.2 Test Requirements .............................................................................................................................. 166
A.9.1.3A GSM Carrier RSSI .................................................................................................................................. 167
A.9.1.3A.1 Test Purpose and Environment........................................................................................................... 167
A.9.1.3A.2 Test Requirements .............................................................................................................................. 167
A.9.1.3B Transport channel BLER.......................................................................................................................... 168
A.9.1.3C UE transmitted power .............................................................................................................................. 168
A.9.1.3C.1 Test Purpose and Environment........................................................................................................... 168
A.9.1.3C.1.1 Test procedure.............................................................................................................................. 168
A.9.1.3C.2 Test Requirements .............................................................................................................................. 168
A.9.1.4 SFN-CFN observed time difference......................................................................................................... 169
A.9.1.4.1 Test Purpose and Environment........................................................................................................... 169
A.9.1.4.1.1 Intra frequency test parameters ..................................................................................................... 169
A.9.1.4.1.2 Inter frequency test parameters ..................................................................................................... 169
A.9.1.4.2 Test Requirements .............................................................................................................................. 170
A.9.1.5 SFN-SFN observed time difference ......................................................................................................... 170
A.9.1.5.1 SFN-SFN observed time difference type 1......................................................................................... 170
A.9.1.5.1.1 Test Purpose and Environment ..................................................................................................... 170
A.9.1.5.1.2 Test Requirements ........................................................................................................................ 171
A.9.1.5.2 SFN-SFN observed time difference type 2 without IPDL period active ............................................ 171
A.9.1.5.2.1 Test Purpose and Environment ..................................................................................................... 171
A.9.1.5.2.2 Test Requirements ........................................................................................................................ 172
A.9.1.5.3 SFN-SFN observed time difference type 2 with IPDL period active ................................................. 172
A.9.1.5.3.1 Test Purpose and Environment ..................................................................................................... 172
A.9.1.5.3.2 Test Requirements ........................................................................................................................ 173
A.9.1.6 UE Rx-Tx time difference....................................................................................................................... 173
A.9.1.6.1 UE Rx-Tx time difference type 1 ....................................................................................................... 173
A.9.1.6.1.1 Test Purpose and Environment ..................................................................................................... 173
A.9.1.6.1.2 Test Requirements ........................................................................................................................ 174
A.9.1.6.2 UE Rx-Tx time difference type 2 ....................................................................................................... 174
A.9.1.6.2.1 Test Purpose and Environment ..................................................................................................... 174
A.9.1.6.2.2 Test Requirements ........................................................................................................................ 175
A.9.1.7 Void......................................................................................................................................................... 175
A.9.1.8 Void......................................................................................................................................................... 175
3GPP
Release 7 11 3GPP TS 25.133 V7.3.0 (2006-03)
Annex B (informative): Change History ............................................................................................176